From johan at securit.se  Wed Feb  1 03:03:19 2012
From: johan at securit.se (Johan Ryberg)
Date: Tue, 31 Jan 2012 17:03:19 +0100
Subject: [flashboot] Booting with 5.0 image
In-Reply-To: <1328009776.1872.6.camel@terminus>
References: <1328009776.1872.6.camel@terminus>
Message-ID: <CAG9dXUyyrcX_=BrNDXz--0gLNgW3ArDdj-vgDNGvo0kQcKyRsg@mail.gmail.com>

Is that everything that happens? No more output?

//Johan
Den 31 jan 2012 12:36 skrev "Eric Boudrand" <eric.boudrand at caramail.com>:

> Hi,
>
> I have tested SOEKRIS4521-50.image on a Soekris NET4511. The boot
> sequence failed with this log :
>
> boot>
> booting hd0a:/bsd: 53407060+463132 [61+127216+116991]=0x339ba3c
> entry point at 0x200120
>
> [ using 244684 bytes of bsd ELF symbol table ]
> Copyright (c) 1982, 1986, 1989, 1991, 1993
>        The Regents of the University of California.  All rights reserved.
> Copyright (c) 1995-2011 OpenBSD. All rights reserved.
> http://www.OpenBSD.org
>
> OpenBSD 5.0 (SOEKRIS4521) #0: Wed Nov  2 12:07:42 MDT 2011
>
> root at i386.builder:/obj/SOEKRIS4521
> cpu0: AMD Am486DX4 W/B or Am5x86 W/B 150 ("AuthenticAMD" 486-class)
> cpu0: FPU
> real mem  = 66646016 (63MB)
> avail mem = 12173312 (11MB)
> mainbus0 at root
> bios0 at mainbus0: AT/286+ BIOS, date 20/31/19, BIOS32 rev. 0 @ 0xf7840
> pcibios0 at bios0: rev 2.0 @ 0xf0000/0x10000
> pcibios0: pcibios_get_intr_routing - function not supported
> pcibios0: PCI IRQ Routing information unavailable.
> pcibios0: PCI bus #1 is the last bus
> bios0: ROM list: 0xc8000/0xa000
> cpu0 at mainbus0: (uniprocessor)
> pci0 at mainbus0 bus 0: configuration mode 1 (bios)
> elansc0 at pci0 dev 0 function 0 "AMD ElanSC520 PCI" rev 0x00: product 0
> steppi>
> gpio0 at elansc0: 32 pins
> cbb0 at pci0 dev 9 function 0 "TI PCI1410 CardBus" rev 0x02: irq 10
> sis0 at pci0 dev 18 function 0 "NS DP83815 10/100" rev 0x00, DP83816A: irq
> 11, 8
> nsphyter0 at sis0 phy 0: DP83815 10/100 PHY, rev. 1
> sis1 at pci0 dev 19 function 0 "NS DP83815 10/100" rev 0x00, DP83816A: irq
> 5, a9
> nsphyter1 at sis1 phy 0: DP83815 10/100 PHY, rev. 1
> cardslot0 at cbb0 slot 0 flags 0
> cardbus0 at cardslot0: bus 1 device 0 cacheline 0x10, lattimer 0x3f
> pcmcia0 at cardslot0
> isa0 at mainbus0
> com0 at isa0 port 0x3f8/8 irq 4: ns16550a, 16 byte fifo
> com0: console
> com1 at isa0 port 0x2f8/8 irq 3: ns16550a, 16 byte fifo
> pckbc0 at isa0 port 0x60/5
> pckbd0 at pckbc0 (kbd slot)
> pckbc0: using irq 1 for kbd slot
> wskbd0 at pckbd0: console keyboard
> wdc0 at isa0 port 0x1f0/8 irq 14
> wd0 at wdc0 channel 0 drive 0: <SanDisk SDCFH-004G>
> wd0: 1-sector PIO, LBA48, 3815MB, 7813120 sectors
> wd0(wdc0:0:0): using BIOS timings
> npx0 at isa0 port 0xf0/16: reported by CPUID; using exception 16
>
> Any suggestion is welcome.
>
> Regards.
>
> ?ric Boudrand
>
>
> _______________________________________________
> flashboot mailing list
> flashboot at mindrot.org
> https://lists.mindrot.org/mailman/listinfo/flashboot
>
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://lists.mindrot.org/pipermail/flashboot/attachments/20120131/4359e340/attachment.html>

From eric.boudrand at caramail.com  Wed Feb  1 03:43:30 2012
From: eric.boudrand at caramail.com (Eric Boudrand)
Date: Tue, 31 Jan 2012 17:43:30 +0100
Subject: [flashboot] Booting with 5.0 image
In-Reply-To: <CAG9dXUyyrcX_=BrNDXz--0gLNgW3ArDdj-vgDNGvo0kQcKyRsg@mail.gmail.com>
References: <1328009776.1872.6.camel@terminus>
 <CAG9dXUyyrcX_=BrNDXz--0gLNgW3ArDdj-vgDNGvo0kQcKyRsg@mail.gmail.com>
Message-ID: <1328028210.1872.29.camel@terminus>

Hi,

Exactly. No more than that :(
If I plug a PCMCIA Wireless card, the log is finishing by  :

wd0: 1-sector PIO, LBA48, 3815MB, 7813120 sectors                               
wd0(wdc0:0:0): using BIOS timings                                               
npx0 at isa0 port 0xf0/16: reported by CPUID; using exception 16                
wi0 at pcmcia0 function 0 "INTERSIL, HFA384x/IEEE, Version 01.02" port 0xa000/64
wi0: PRISM2.5 ISL3873 (0x800c), Firmware 1.1.0 (primary), 1.4.9 (station), addr3

And nothing more.

I can boot with a Monowall system. Boot up log for Monowall is :

Consoles: internal video/keyboard  
BIOS drive C: is disk0
BIOS 639kB/64512kB available memory                                             
                                                                                
FreeBSD/i386 bootstrap loader, Revision 1.1                                     
(root at mb64.neon1.net, Thu Jul 23 20:56:49 CEST 2009)                            
/kernel text=0x368050 data=0x3d474+0x22ef4 syms=[0x4+0x47050+0x4+0x5acc6]       
Copyright (c) 1992-2008 The FreeBSD Project.                                    
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994        
        The Regents of the University of California. All rights reserved.       
FreeBSD is a registered trademark of The FreeBSD Foundation.                    
FreeBSD 6.4-RELEASE-p5 #0: Sun Jan  9 22:24:57 CET 2011                         
    root at mb64.neon1.net:/usr/src/sys/i386/compile/M0N0WALL_EMBEDDED             
Timecounter "i8254" frequency 1193182 Hz quality 0                              
CPU: AMD Enhanced Am486DX4/Am5x86 Write-Back (486-class CPU)                    
  Origin = "AuthenticAMD"  Id = 0x494  Stepping = 4                             
  Features=0x1<FPU>                                                             
real memory  = 67108864 (64 MB)                                                 
avail memory = 39530496 (37 MB)                                                 
wlan: mac acl policy registered                                                 
ath_hal: 0.9.20.3 (AR5210, AR5211, AR5212, RF5111, RF5112, RF2413, RF5413)      
cpu0 on motherboard                                                             
sysctl machdep.i8254_freq=1189161 returns 0                                     
Timecounter "ELAN" frequency 8333333 Hz quality 1000                            
pcib0: <AMD Elan SC520 host to PCI bridge> pcibus 0 on motherboard              
pci0: <PCI bus> on pcib0                                                        
cbb0: <TI1410 PCI-CardBus Bridge> mem 0xa0000000-0xa0000fff irq 10 at device 9.0
cardbus0: <CardBus bus> on cbb0                                                 
pccard0: <16-bit PCCard bus> on cbb0                                            
sis0: <NatSemi DP8381[56] 10/100BaseTX> port 0xe100-0xe1ff mem 0xa0001000-0xa000
sis0: Silicon Revision: DP83816A                                                
miibus0: <MII bus> on sis0                                                      
nsphyter0: <DP83815 10/100 media interface> on miibus0                          
nsphyter0:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto                
sis0: Ethernet address: 00:00:24:c1:f3:58                                       
sis1: <NatSemi DP8381[56] 10/100BaseTX> port 0xe200-0xe2ff mem 0xa0002000-0xa000
sis1: Silicon Revision: DP83816A                                                
miibus1: <MII bus> on sis1                                                      
nsphyter1: <DP83815 10/100 media interface> on miibus1                          
nsphyter1:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto                
sis1: Ethernet address: 00:00:24:c1:f3:59                                       
isa0: <ISA bus> on motherboard                                                  
pmtimer0 on isa0                                                                
orm0: <ISA Option ROM> at iomem 0xc8000-0xd1fff on isa0                         
ata0 at port 0x1f0-0x1f7,0x3f6 irq 14 on isa0                                   
ata1 at port 0x170-0x177,0x376 irq 15 on isa0                                   
sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0                               
sio0: type 16550A, console                                                      
sio1 at port 0x2f8-0x2ff irq 3 on isa0                                          
sio1: type 16550A                                                               
Timecounters tick every 1.000 msec                                              
Elan-mmcr driver: MMCR at 0xc68ef000.                                           
Elan-mmcr Soekris net45xx comBIOS ver. 1.23 20031119 Copyright (C) 2000-2003    
Fast IPsec: Initialized Security Association Processing.                        
IP Filter: v4.1.33 initialized.  Default = block all, Logging = enabled         
md0: Preloaded image </mfsroot> 16777216 bytes at 0xc086b0e8                    
ad0: FAILURE - SET_MULTI status=51<READY,DSC,ERROR> error=4<ABORTED>            
ad0: 3825MB <SanDisk SDCFH-004G HDX 5.11> at ata0-master PIO4

It seems to be more available memory for FreeBSD system than OpenBSD system (37 MB vs 11 MB).

?ric 

Le mardi 31 janvier 2012 ? 17:03 +0100, Johan Ryberg a ?crit :
> Is that everything that happens? No more output? 
> 
> //Johan 
> 
> Den 31 jan 2012 12:36 skrev "Eric Boudrand"
> <eric.boudrand at caramail.com>:
>         Hi,
>         
>         I have tested SOEKRIS4521-50.image on a Soekris NET4511. The
>         boot
>         sequence failed with this log :
>         
>         boot>
>         booting hd0a:/bsd: 53407060+463132 [61+127216
>         +116991]=0x339ba3c
>         entry point at 0x200120
>         
>         [ using 244684 bytes of bsd ELF symbol table ]
>         Copyright (c) 1982, 1986, 1989, 1991, 1993
>                The Regents of the University of California.  All
>         rights reserved.
>         Copyright (c) 1995-2011 OpenBSD. All rights reserved.
>         http://www.OpenBSD.org
>         
>         OpenBSD 5.0 (SOEKRIS4521) #0: Wed Nov  2 12:07:42 MDT 2011
>         
>         root at i386.builder:/obj/SOEKRIS4521
>         cpu0: AMD Am486DX4 W/B or Am5x86 W/B 150 ("AuthenticAMD"
>         486-class)
>         cpu0: FPU
>         real mem  = 66646016 (63MB)
>         avail mem = 12173312 (11MB)
>         mainbus0 at root
>         bios0 at mainbus0: AT/286+ BIOS, date 20/31/19, BIOS32 rev. 0
>         @ 0xf7840
>         pcibios0 at bios0: rev 2.0 @ 0xf0000/0x10000
>         pcibios0: pcibios_get_intr_routing - function not supported
>         pcibios0: PCI IRQ Routing information unavailable.
>         pcibios0: PCI bus #1 is the last bus
>         bios0: ROM list: 0xc8000/0xa000
>         cpu0 at mainbus0: (uniprocessor)
>         pci0 at mainbus0 bus 0: configuration mode 1 (bios)
>         elansc0 at pci0 dev 0 function 0 "AMD ElanSC520 PCI" rev 0x00:
>         product 0 steppi>
>         gpio0 at elansc0: 32 pins
>         cbb0 at pci0 dev 9 function 0 "TI PCI1410 CardBus" rev 0x02:
>         irq 10
>         sis0 at pci0 dev 18 function 0 "NS DP83815 10/100" rev 0x00,
>         DP83816A: irq 11, 8
>         nsphyter0 at sis0 phy 0: DP83815 10/100 PHY, rev. 1
>         sis1 at pci0 dev 19 function 0 "NS DP83815 10/100" rev 0x00,
>         DP83816A: irq 5, a9
>         nsphyter1 at sis1 phy 0: DP83815 10/100 PHY, rev. 1
>         cardslot0 at cbb0 slot 0 flags 0
>         cardbus0 at cardslot0: bus 1 device 0 cacheline 0x10, lattimer
>         0x3f
>         pcmcia0 at cardslot0
>         isa0 at mainbus0
>         com0 at isa0 port 0x3f8/8 irq 4: ns16550a, 16 byte fifo
>         com0: console
>         com1 at isa0 port 0x2f8/8 irq 3: ns16550a, 16 byte fifo
>         pckbc0 at isa0 port 0x60/5
>         pckbd0 at pckbc0 (kbd slot)
>         pckbc0: using irq 1 for kbd slot
>         wskbd0 at pckbd0: console keyboard
>         wdc0 at isa0 port 0x1f0/8 irq 14
>         wd0 at wdc0 channel 0 drive 0: <SanDisk SDCFH-004G>
>         wd0: 1-sector PIO, LBA48, 3815MB, 7813120 sectors
>         wd0(wdc0:0:0): using BIOS timings
>         npx0 at isa0 port 0xf0/16: reported by CPUID; using exception
>         16
>         
>         Any suggestion is welcome.
>         
>         Regards.
>         
>         ?ric Boudrand
>         
>         
>         _______________________________________________
>         flashboot mailing list
>         flashboot at mindrot.org
>         https://lists.mindrot.org/mailman/listinfo/flashboot



From stu at spacehopper.org  Wed Feb  1 04:15:27 2012
From: stu at spacehopper.org (Stuart Henderson)
Date: Tue, 31 Jan 2012 17:15:27 +0000
Subject: [flashboot] Booting with 5.0 image
In-Reply-To: <1328009776.1872.6.camel@terminus>
References: <1328009776.1872.6.camel@terminus>
Message-ID: <20120131171527.GO23155@symphytum.spacehopper.org>

Looks a bit like there's no getty running on the serial port..
Do you get further if you boot into single-user mode?


On 2012/01/31 12:36, Eric Boudrand wrote:
> Hi,
> 
> I have tested SOEKRIS4521-50.image on a Soekris NET4511. The boot
> sequence failed with this log :
> 
> boot>                                                                           
> booting hd0a:/bsd: 53407060+463132 [61+127216+116991]=0x339ba3c                 
> entry point at 0x200120                                                         
>                                                                                 
> [ using 244684 bytes of bsd ELF symbol table ]                                  
> Copyright (c) 1982, 1986, 1989, 1991, 1993                                      
>         The Regents of the University of California.  All rights reserved.      
> Copyright (c) 1995-2011 OpenBSD. All rights reserved. http://www.OpenBSD.org   
>                                                                                 
> OpenBSD 5.0 (SOEKRIS4521) #0: Wed Nov  2 12:07:42 MDT 2011                      
> 
> root at i386.builder:/obj/SOEKRIS4521                                          
> cpu0: AMD Am486DX4 W/B or Am5x86 W/B 150 ("AuthenticAMD" 486-class)             
> cpu0: FPU                                                                       
> real mem  = 66646016 (63MB)                                                     
> avail mem = 12173312 (11MB)                                                     
> mainbus0 at root                                                                
> bios0 at mainbus0: AT/286+ BIOS, date 20/31/19, BIOS32 rev. 0 @ 0xf7840         
> pcibios0 at bios0: rev 2.0 @ 0xf0000/0x10000                                    
> pcibios0: pcibios_get_intr_routing - function not supported                     
> pcibios0: PCI IRQ Routing information unavailable.                              
> pcibios0: PCI bus #1 is the last bus                                            
> bios0: ROM list: 0xc8000/0xa000                                                 
> cpu0 at mainbus0: (uniprocessor)                                                
> pci0 at mainbus0 bus 0: configuration mode 1 (bios)                             
> elansc0 at pci0 dev 0 function 0 "AMD ElanSC520 PCI" rev 0x00: product 0 steppi>
> gpio0 at elansc0: 32 pins                                                       
> cbb0 at pci0 dev 9 function 0 "TI PCI1410 CardBus" rev 0x02: irq 10             
> sis0 at pci0 dev 18 function 0 "NS DP83815 10/100" rev 0x00, DP83816A: irq 11, 8
> nsphyter0 at sis0 phy 0: DP83815 10/100 PHY, rev. 1                             
> sis1 at pci0 dev 19 function 0 "NS DP83815 10/100" rev 0x00, DP83816A: irq 5, a9
> nsphyter1 at sis1 phy 0: DP83815 10/100 PHY, rev. 1                             
> cardslot0 at cbb0 slot 0 flags 0                                                
> cardbus0 at cardslot0: bus 1 device 0 cacheline 0x10, lattimer 0x3f             
> pcmcia0 at cardslot0                                                            
> isa0 at mainbus0                                                                
> com0 at isa0 port 0x3f8/8 irq 4: ns16550a, 16 byte fifo                         
> com0: console                                                                   
> com1 at isa0 port 0x2f8/8 irq 3: ns16550a, 16 byte fifo                         
> pckbc0 at isa0 port 0x60/5                                                      
> pckbd0 at pckbc0 (kbd slot)                                                     
> pckbc0: using irq 1 for kbd slot                                                
> wskbd0 at pckbd0: console keyboard                                              
> wdc0 at isa0 port 0x1f0/8 irq 14                                                
> wd0 at wdc0 channel 0 drive 0: <SanDisk SDCFH-004G>                             
> wd0: 1-sector PIO, LBA48, 3815MB, 7813120 sectors                               
> wd0(wdc0:0:0): using BIOS timings                                               
> npx0 at isa0 port 0xf0/16: reported by CPUID; using exception 16   
> 
> Any suggestion is welcome.
> 
> Regards.
> 
> ?ric Boudrand
> 
> 
> _______________________________________________
> flashboot mailing list
> flashboot at mindrot.org
> https://lists.mindrot.org/mailman/listinfo/flashboot

From eric.boudrand at caramail.com  Wed Feb  1 05:15:53 2012
From: eric.boudrand at caramail.com (Eric Boudrand)
Date: Tue, 31 Jan 2012 19:15:53 +0100
Subject: [flashboot] Booting with 5.0 image
In-Reply-To: <20120131171527.GO23155@symphytum.spacehopper.org>
References: <1328009776.1872.6.camel@terminus>
 <20120131171527.GO23155@symphytum.spacehopper.org>
Message-ID: <1328033753.1872.37.camel@terminus>

Hi,

Le mardi 31 janvier 2012 ? 17:15 +0000, Stuart Henderson a ?crit :
> Looks a bit like there's no getty running on the serial port..
> Do you get further if you boot into single-user mode?

Same result with boot -s

?ric



From eric.boudrand at caramail.com  Wed Feb  1 05:20:34 2012
From: eric.boudrand at caramail.com (Eric Boudrand)
Date: Tue, 31 Jan 2012 19:20:34 +0100
Subject: [flashboot] Booting with 5.0 image
In-Reply-To: <CAGG-Ge6h7Rt2NA7BTBKzX8msmpxfOBxzWtnhGsq9r4cVwG6uXQ@mail.gmail.com>
References: <1328009776.1872.6.camel@terminus>
 <CAG9dXUyyrcX_=BrNDXz--0gLNgW3ArDdj-vgDNGvo0kQcKyRsg@mail.gmail.com>
 <1328028210.1872.29.camel@terminus>
 <CAGG-Ge6h7Rt2NA7BTBKzX8msmpxfOBxzWtnhGsq9r4cVwG6uXQ@mail.gmail.com>
Message-ID: <1328034034.1872.40.camel@terminus>

Hi,

> Have you tried with 4.9, I believe the memory disk size changed
> drastically in 5.0 bringing it to around 48 MB, it was much smaller in
> 4.9 which may give you enough room to boot.
> 
No. Only 5.0. I have to build a 4.9 system then. Or I will try to
download older binary releases.

?ric


From nicboul at gmail.com  Mon Feb 13 04:20:37 2012
From: nicboul at gmail.com (NICOLAS BOULIANE)
Date: Sun, 12 Feb 2012 12:20:37 -0500
Subject: [flashboot]  Booting with 5.0 image
Message-ID: <CAAt=MPwohp71U8ycbrwe5e-J3dypo24JmO57aEerpWcu_RqvgQ@mail.gmail.com>

Eric Boudrand,

What file have you copied ? bsd or bsd.rd


peace,
Nicolas Bouliane