[flashboot] Still searching for a stable OpenBSD 4.3 and flasboot branch.

[Russell Sutherland]

I failed again today to get a fresh OpenBSD 4.3 source tree
(using cvsup):

*default host=cvsup.usa.openbsd.org
*default base=/var
*default prefix=/usr
*default release=cvs
*default delete use-rel-suffix compress

OpenBSD-src   tag=OPENBSD_4_3


and flashboot: (flashboot-SNAP-20080410.tar.gz)

After a:

# build-release.sh
# build-largekernel.sh SOEKRIS4801
# build-diskimage.sh

and moving the image to a CF card I get:

>> OpenBSD/i386 BOOT 3.01
-
com0: 19200 baud
switching console to com0

[ using 244856 bytes of bsd ELF symbol table ]
Copyright (c) 1982, 1986, 1989, 1991, 1993
        The Regents of the University of California.  All rights reserved.
Copyright (c) 1995-2008 OpenBSD. All rights reserved.  http://www.OpenBSD.org

OpenBSD 4.3 (SOEKRIS4801.LARGE) #0: Thu Apr 10 09:00:56 EDT 2008
    root at bureau10:/usr/local/src/flashboot/obj/SOEKRIS4801.LARGE
cpu0: Geode(TM) Integrated Processor by National Semi ("Geode by NSC"
586-class) 267 MHz
cpu0: FPU,TSC,MSR,CX8,CMOV,MMX
cpu0: TSC disabled
real mem  = 133787648 (127MB)
avail mem = 104435712 (99MB)
mainbus0 at root
bios0 at mainbus0: AT/286+ BIOS, date 20/80/03, BIOS32 rev. 0 @ 0xf7840
pcibios0 at bios0: rev 2.0 @ 0xf0000/0x10000
pcibios0: pcibios_get_intr_routing - function not supported
pcibios0: PCI IRQ Routing information unavailable.
pcibios0: PCI bus #0 is the last bus
bios0: ROM list: 0xc8000/0x9000
cpu0 at mainbus0
pci0 at mainbus0 bus 0: configuration mode 1 (bios)
pchb0 at pci0 dev 0 function 0 "Cyrix GXm PCI" rev 0x00
sis0 at pci0 dev 6 function 0 "NS DP83815 10/100" rev 0x00, DP83816A:
irq 10, address 00:00:24:c2:3e:b0
nsphyter0 at sis0 phy 0: DP83815 10/100 PHY, rev. 1
sis1 at pci0 dev 7 function 0 "NS DP83815 10/100" rev 0x00, DP83816A:
irq 10, address 00:00:24:c2:3e:b1
nsphyter1 at sis1 phy 0: DP83815 10/100 PHY, rev. 1
sis2 at pci0 dev 8 function 0 "NS DP83815 10/100" rev 0x00, DP83816A:
irq 10, address 00:00:24:c2:3e:b2
nsphyter2 at sis2 phy 0: DP83815 10/100 PHY, rev. 1
pcib0 at pci0 dev 18 function 0 "NS SC1100 ISA" rev 0x00
"NS SC1100 SMI" rev 0x00 at pci0 dev 18 function 1 not configured
pciide0 at pci0 dev 18 function 2 "NS SCx200 IDE" rev 0x01: DMA,
channel 0 wired to compatibility, channel 1 wired to compatibility
wd0 at pciide0 channel 0 drive 1: <CF CARD 1GB>
wd0: 1-sector PIO, LBA, 967MB, 1981728 sectors
wd0(pciide0:0:1): using PIO mode 4, DMA mode 2
geodesc0 at pci0 dev 18 function 5 "NS SC1100 X-Bus" rev 0x00: iid 6
revision 3 wdstatus 0
ohci0 at pci0 dev 19 function 0 "Compaq USB OpenHost" rev 0x08: irq
11, version 1.0, legacy support
isa0 at pcib0
pckbc0 at isa0 port 0x60/5
pckbd0 at pckbc0 (kbd slot)
pckbc0: using irq 1 for kbd slot
wskbd0 at pckbd0: console keyboard
nsclpcsio0 at isa0 port 0x2e/2: NSC PC87366 rev 9: GPIO VLM TMS
gpio0 at nsclpcsio0: 29 pins
gscsio0 at isa0 port 0x15c/2: SC1100 SIO rev 1:
npx0 at isa0 port 0xf0/16: reported by CPUID; using exception 16
pccom0 at isa0 port 0x3f8/8 irq 4: ns16550a, 16 byte fifo
pccom0: console
pccom1 at isa0 port 0x2f8/8 irq 3: ns16550a, 16 byte fifo
usb0 at ohci0: USB revision 1.0
uhub0 at usb0 "Compaq OHCI root hub" rev 1.00/1.00 addr 1
biomask fbe5 netmask ffe5 ttymask ffe7
rd0: fixed, 40960 blocks
root on rd0a swap on rd0b dump on rd0b
panic: init died (signal 0, exit 4)
Stopped at      Debugger+0x4:   leave
RUN AT LEAST 'trace' AND 'ps' AND INCLUDE OUTPUT WHEN REPORTING THIS PANIC!
DO NOT EVEN BOTHER REPORTING THIS WITHOUT INCLUDING THAT INFORMATION!
ddb>
ddb> trace
Debugger(d556cecc,100,d556cf00,d02abd72,d0493440) at Debugger+0x4
panic(d0493440,0,4,d02b03d8,d4dce150) at panic+0x8b
exit1(d4dcb000,400,1,0) at exit1+0x32
sys_exit(d4dcb000,d556cf58,d556cf50,d0402a75) at sys_exit+0x22
syscall() at syscall+0x1d3
--- syscall (number 1) ---
0x3f1b943:

ddb> ps
   PID   PPID   PGRP    UID  S       FLAGS  WAIT          COMMAND
    13      0      0      0  3    0x100200  bored         crypto
    12      0      0      0  3    0x100200  aiodoned      aiodoned
    11      0      0      0  3    0x100200  syncer        update
    10      0      0      0  3    0x100200  cleaner       cleaner
     9      0      0      0  3    0x100200  reaper        reaper
     8      0      0      0  3    0x100200  pgdaemon      pagedaemon
     7      0      0      0  3    0x100200  pftm          pfpurge
     6      0      0      0  3    0x100200  usbtsk        usbtask
     5      0      0      0  3    0x100200  usbevt        usb0
     4      0      0      0  3    0x100200  bored         syswq
     3      0      0      0  3    0x100200                idle0
     2      0      0      0  3    0x100200  kmalloc       kmthread
*    1      0      0      0  7      0x4000                init
     0     -1      0      0  3     0x80200  scheduler     swapper




-- 
Russell Sutherland
russ at quist.ca
+1.416.696.7600